Table of Contents
- 1 Where is parking sensor module?
- 2 How do I disable PDC on my BMW?
- 3 What is PDC malfunction in BMW?
- 4 How do I test a PDC module?
- 5 What is a PDC module?
- 6 What is PDC failure?
- 7 Can parking sensors be adjusted?
- 8 How does a PDC sensor work?
- 9 What is the meaning of parking sensor?
- 10 Where does the bottom connector go on a BMW 5?
- 11 Where are the front sensors on a BMW 5?
- 12 How to diagnose a PDC fault in BMW 5?
- 13 What is the fault code for a BMW 5?
Where is parking sensor module?
It’s a small square plastic component, that says “REAR PARKING AID MODULE” on it, and will have the part number F1ET-15K866-AG. To access it, remove the cover on the driver’s side — You’ll see there’s a very small squarish panel there, on the back of the seat — and You should immediately see it.
How do I disable PDC on my BMW?
The system can be temporarily disabled by either applying the brakes or pressing the steering wheel button once. The green light on the speedometer display will change to amber.
What is PDC malfunction in BMW?
BMW Parking Assist Malfunction, Auto PDC failure, and no parking assistance may display on the iDrive screen due to a faulty sensor, defective control module, or software issues with the Park Assist module. Anytime the car speed is lower than 22 mph, it observes the potential parking spaces.
How do I test a PDC module?
“You can check the sensors by engaging the PDC, and then passing your hand across in front of each sensor. They should click audibly. If no clicks from any of them, then its likely they are not being driven at all.” To check power at the module, its pin 7 on connector X300.
What is a PDC module?
What park distance control (PDC) really means: Basics. The parking assistant is a driver assistance system that supports drivers during manoeuvring and parking and warns them of obstacles in the immediate vicinity of the vehicle. If an obstacle is detected, the driver is informed of this either visually or acoustically …
What is PDC failure?
Once 2 or more sensors fail the controller shutdowns and you’ll also get the PDC Failure messages. If you have the car in reverse to activate the PDC and then put your ear right up to each sensor you should hear a “clicking”, do this on all front and rear sensors.
Can parking sensors be adjusted?
Parking sensor range to an obstruction can vary from 0 to 3 meters, this can be adjusted to your preference by using the programming button (See Programming) or the AL Priority Setup application . You can choose between 8 levels of sensitivity.
How does a PDC sensor work?
These sensors work either on ultrasonic or electromagnetic principle, with former being more popular. When the driver engages reverse gear, rear parking sensors get activated automatically and send ultrasonic waves. When these waves hit the nearby object, they get reflected and are captured again by the sensors.
What is the meaning of parking sensor?
Parking sensors are proximity sensors for road vehicles designed to alert the driver of obstacles while parking.
The “TOP” connector goes to the front. The “MIDDLE” goes to the rear. “BOTTOM” is the power supply part of the module. Since these cars were produced in both LHD and RHD versions it would be better todescribe the error codes like this:
Where are the front sensors on a BMW 5?
Note that Front side sensors can be accessed by removing the headlights, front middle sensors by removing the kidney grills and you’ll need to take the rear bumper off to change any at the rear. Hope this’ll help someone quickly diagnose why their sensors aren’t working. Nice one.
How to diagnose a PDC fault in BMW 5?
009E3A Inverter VMR (Vorn Mitte Rechts – Front Middle Right) X X 0 X 009E39 Inverter VML (Vorn Mitte Links – Front Middle Left) X 0 X X 009E35 Inverter HML (Hinten Mitte Links – Rear Middle Left) X 0 X X 009E36 Inverter HMR (Hinten Mitte Rechts – Rear Middle Right) X X 0 X The fault code I have is 009E37.
What is the fault code for a BMW 5?
The sensor in the sequence immediately after the sensor reporting the fault is the broken sensor. I was picking up fault codes for 009E38 so by changing the sensor on the Front Passenger Middle the rest of my sensors came back on line.